High Purity Tantalum Carbide TaC Powder Cas 12070-06-3, 99.9%

Tantalum-Carbide TaC Powder :
Tantalum carbide It is a metallic cubic, crystalline powder. This forms a binary chemical compound of carbon and tantalum. They are extremely tough, delicate, and refractory ceramic material with metallic conductivity. They are typically sintered to make brownish-gray, powdery forms. It is a sodium chloride-type cubic crystal. Presently, tantalum carbid is used in the cemented carbide sintered seed grain growth inhibitor. This has a notable effect on grain growth and has a density at 14.3g/cm3.

Tantalum caride is not soluble and very difficult to dissolve in water. It is resistant to oxidation and can be easily melted with potassium pyrosulfate. Tantalum carbid has high electrical conductivity. At room temperature it is resistant to 30O and shows superconducting qualities. Tantalum carbonide is used for cutting and powder metallurgy. Chemical vapor deposition can also be used to make hard wear-resistant tools and molds. Wear-resistant and corrosion resistant structural components can improve the alloy's toughness. You can use the golden-yellow sintered body made of tantalum caride as watch decorations.

This complex combination of covalent elements and metal ions makes the bond between tantalum carbide atoms and carbon atoms complex. Carbide materials are very tough and hard due to their strong covalent component. TaC is a good example. It has a microhardness range of 1600 to 2000 km/mm2 (9mH), an elastic modulus between 285gPa and 110kg/mm2. Tantalum, on the other hand, has equivalent values at 186gPa. TAC has a higher carbon content, which increases hardness and yield stress.

When tungsten carbide alloy is being used in cutting applications, it may be added as tantalum carbonide.
Tantalum carbide melting point Tantalum carbide's melting point is 3880°C depending on how pure it is and what measurement conditions are used. This is one of the most important binary compounds. The melting point for tantalum carbide ha is about 3942degC higher than that of carbideclam, which has an equivalent melting point to TaC.

To receive the most current information, send us an inquiry tantalum carbide price Please fill out the form below if you wish to buy Tantalum Carbide Powder In bulk.

Technical specifications of Tantalum Carbide TaC powder
Number of the CAS: 12070-06-3
TaC powder true density: 13.9g/cm3 Tantalum carbide
1.25g/cm3 - Tantalum carbide TaC dust Bulk Density
Crystal Structure of the Tantalum carbide TaC Powder: Cubic
Tantalum carbide TaC powder: 1000 nm. (Can be customized).
15 m2/g Tantalum carbide TaC mould SSA
TaC powder purity: 9+% Tantalum carbide
TaC powder Tantalum Carbide Solubility: Insoluble
TaC powder Tantalum Caride TaC appearance: Black-gray, odorless

T.C	F.C	O	N	Al	Fe	Na	Ca	K	Si
>6.32%	<0.08%	<0.3%	<0.003%	<0.004%	<0.042%	<0.003%	<0.003%	<0.004%	<0.003%

Tantalum carbide Properties:
Tantalum carbonide TaC (Mohs hardness 9.0-10) is a hard refractory clay material. It's used for tool bits that are designed to cut tools. Diamond can surpass this level of hardness.
It's a dark brown powder, which is usually sintered.
This is often used in fine-crystalline additions to tungsten carbide alloys.
Tantalum carbonide is the only stoichiometric binary material with the highest known melting points at 4150 K (33880degC) or boiling point of 5500 oC.
TaC0.89, a substoichiometric chemical has a melting point of 4270 K (4000degC).

How does Tantalum-Carbide TaC Powder get made?
Tac powder is made by heating graphite powder and adding it to a vacuum. Heat was used to heat the powder at approximately 2000°C using an oven or arc melting. An alternative method involves heating carbon tantalum dioxide in a vacuum or hydrogen atmosphere to reduce the temperature. However, this technology does not allow for thermometrically controlled control over the product. TAC directly is made from the component through self-propagating, high-temperature synthesizing.

Tantalum Carbide Uses :
Carbide, capacitors and electronic components are the main applications of tantalum caride. In order to improve the physical properties, carbides are commonly added to the powder wear of tungsten carbide/cobalt (WC/CO) to increase their effectiveness in sintering.
Tantalum carbide is also used to inhibit the formation of large particles in order to achieve optimum hardness.
You can also use it as steel mold coatings for aluminum alloy injection moulding. This provides hard wear-resistant and low friction surfaces.
You can also use carbides to create sharp instruments with high mechanical resistance and hardness. Tantalum carbide can be also used for the following:
1. Cemented carbide
Tintalum carbide plays a key role in cemented carbide. The alloy's properties are improved by increasing fibrous tissue and phase conversion kinetics. Alloys have higher strength and stability.
2. Electronic industry
While Natunction shares many benefits with carbide nanomaterials, it has its own special side. It has high hardness, 9-10 at normal temperature, and a high melting point of 3880 degrees C.
3. High-temperature Alloy
The melting of carbide is, preferably, a tantalum carbonide(TAC) at 3890°C and carbide (37880°C), then carbide (2500°C). The materials' mechanical properties are excellent at high temperatures.

Storage condition TaC powder Tantalum carbide :
TaC powder's dispersion and usage performance will be affected by the damp reunion. Tantalum carbide TaC should therefore be vacuum packed and kept in cool, dry rooms. Tantalum Carbide TaC Powder cannot be exposed to the air. Ti2AlC should not be exposed to stress.

Shipping and Packing of Tantalum Caride TaC Powder :
We offer many packing options that are dependent on the Tantalum carbid TaC powder amount.
Packaging of Tantalum Carbide TaC powder: Vacuum packaging, 100g,500g, or 1kg/bag. 25kg/barrel. Or as you request.
Tantalum carbide TaC (tantalum powder) shipping: Could be shipped by sea, air or express, as long as the payment receipt has been received.


Tatayoung advanced materials Nano Technology Co. Ltd., (Tatayoung), is a trusted global supplier and manufacturer. It has over 12-years of experience in providing high-quality chemical materials and Nanomaterials. This includes boride, nitride, graphite, sulfide, 3D printing powders, and sulfide.
Are you looking for? Quality tantalum carbide powder Feel free to contact us. Get in touch You can also send us an enquiry. ( brad@ihpa.net )